Force sensitive resistor to measure weight

Force Sensitive Resistor - Small SEN-09673 Circular. An FSR Force Sensitive Resistor is a sensor that allows you to measure physical pressure weight and squeezing.

Force Sensitive Resistor - Small SEN-09673 Circular.

Force sensitive resistor to measure weight. FSRs are sensors that allow you to detect physical pressure squeezing and weight. They are simple to use and low cost. This is a photo of an FSR specifically the Interlink 402 model.

The 12 diameter round part is the sensitive bit. The FSR is made of 2 layers separated by a spacer. 0 to 20 lb.

0 to 100 Newtons applied evenly over the 0125 sq in surface area Power supply. Uses less than 1mA of current depends on any pullupdown resistors used and supply voltage Datasheet httpsadafruitclQ note there are some mathematical inconsistancies in here How to measure forcepressure with an FSR. An FSR Force Sensitive Resistor is a sensor that allows you to measure physical pressure weight and squeezing.

They are pretty much used in DIY electronics as they are available at low cost. In this Instructable Ill show you how to Interface an FSR to Arduino and change the brightness of an LED depending on the pressure applied on the FSR. Up to 7 cash back Force-sensing resistors are intended for applications where a delta in applied force is to be detected.

They are not intended for high accuracy or specific weight measurement applications. 3970 x 3970mm active area. Connector housing female equivalent to Nicomatic 14106-12 and OF02.

When force is applied to a force sensing resistor the conductance response as a function of force is linear. Most engineers have learned that the formula for force is an objects mass multiplied by its acceleration or FMA or applied pressure multiplied by the contact area FPArea. Accurately measures force load on a single sensing point.

Tend to be bulky and heavy thus making them difficult to embed into compact spaces or designs. Require significantly more power than other sensor technologies. Require routine factory re-calibration.

Printed force-sensitive resitors that are used to measure. Force Sensitive Resistor - Small SEN-09673 Circular. 762 mm dia 03 in 01 kg 022 lb 1 kg 22 lb Force Sensitive Resistor 05 SEN-09375 Circular.

127 mm dia 05 in 100 g 022 lb 10 kg 2204 lb Force Sensitive Resistor - Square SEN-09376 Square. 4445 x 4445 mm 175 x 175 in 100 g 022 lb 10 kg 2204 lb Force Sensitive Resistor - Long SEN-09674. 4-Zone sensors measure force applied in each of four cardinal directions.

These are typically placed under buttons in keyboards or remote controls in order to create a pointing mouse. By measuring force on each zone smooth 360 control can be accomplished. Interlink provides both custom sensors and a standard catalog of round.

Force Sensitive Resistors FSR Many embedded applications need to sense physical properties such as force pressure squeezing or approximate weight to be able to interact with the physical world. Force sensitive resistors are a very easy and economical way of sensing whether pressure is being applied at a. FSR is used on boxers targets to collect data about the weight frequency and speed of the trainees punches.

FSRTEK has been involved in the membrane force sensors field as the provider of force sensing resistor service in ChinaWith more than 10 years of experience in the field of membrane force sensors we. There are several resistive based sensors but force sensing resistors operate satisfactorily in difficult environments and also requires a simple interface compared to other resistive based sensors. Force Sensitive Resistor FSR402 Film Pressure Sensor Weight Sensor_.

1 Instead of using a force sensitive resistor use a load cell. This is a 4-wire device with a resistor bridge. The resistance between pairs of wires changes slightly when weight is applied.

Theyre available in a wide range of weight ratings from those suitable for weighing out individual SMD components right up to those used to weigh trucks. Force Sensitive Resistor Tests with Arduino. The datasheet for the RP-S40-ST cites a range of 10g - 10kg but 10kg is fairly large to calibrate without a force tester which we do not have in our lab.

Thus the testing region for the FSR in this case is 20g - 11kg more on this later.